Products

Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Matte Black anodize Knurled thread protector Installation instructions

FX Impact/Wildcat 1/2 x 20 ... $50.00

Note: If you need a shroud extender for your 600mm FX Impact to work with the Saber Tactical TRS rail, you'll need this adapter: A101 This adapter is for Impacts and Wildcats that have the M20x1 male threaded end. It will screw onto your factory shroud and allow you to screw on an LDC with a 1/2 x 20 UNF Female threads. Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Matte Black anodize Knurled thread protecton

FX Shroud Extender 1/2 x 20 Female to 1/2 x 20 Male A101

FX Shroud Extender 1/2 x 20... $35.00

This adapter adds .75 inches to the FX shroud. Female 1/2 x 20 to Male 1/2 x 20 Features: 6061 T6 aluminum length .75 inches Includes thread protector Black anodize Weights: 1.5oz 28MM outer diameter

FX Shroud Extender 1/2 x 20 Female to 1/2 x 20 Male A102

FX Shroud Extender 1/2 x 20... $45.00

This adapter adds 2.5 inches to the FX shroud. Features: 6061 T6 aluminum length 2.5 inches Includes thread protector Black anodize Weights: 3.7oz 28mm outer diameter

FX Wildcat / FX Royale 400/500 Adapter A12

FX Wildcat / FX Royale 400/... $50.00

These adapters are for Wildcat shrouds that extend past the air tube and has female threads once you remove the front shroud cap. It is also compatible with FX Royale 400/500, Boss and Whisper. This adapter is Male to Male, one side is M20x1 that goes into the shroud and the other end is 1/2 x 20 UNF. Features Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip *Note if you have a newer Wildcat, this is not the correct adapter. You will need this one instead: https://donnyfl.com/collections/adapters/products/fx-impact-wildcat-1-2-x-20-unf-adapter-matte-finish-with-thread-protector

FX Wildcat Mag Holder M27 $25.00

With Matt247365 from Airgun Nation's blessing, I am happy to offer these easy to install Wildcat mag holders. Compatible with .177 .22 .25 and .30 caliber. Your magazine clicks securely into the Mag holder using it’s own ball bearing and can rotate for easy loading with one hand while on the gun. As many as 4 Magholders can fit on the Wildcat at one time. You can mount 1, 2, 3 or 4 in a variety of configurations facing either to the front or to the rear and on either side or on both sides. Features: Made of 6061 T6 aluminum black anodize CNC machined Uses 2.5 mm Hex key

FX Wildcat Shroud Extension 1/2 x 20 Adapter A1

FX Wildcat Shroud Extension... $50.00

This shroud extension is for shrouds that sits behind the lower air tube. Female side is M20x1 and male 1/2 x 20. Features Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize 44mm long

Gamo TC35, TC45/ Evanix Rex, Rex P M18x1 Adapter A59

Gamo TC35, TC45/ Evanix Rex... $40.00

*Please note: Take the front cap off your shroud, measure the outer diameter of the threads on the cap. If close to 1.4 inches, use this adapter. Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

Hatsan Blitz 1/2 x 20 Adapt... $40.00

This adapter allows you to screw on an airgun suppressor with 1/2 x 20 threads. I recommend going with the Ronin 1/2 x 20 with this gun. I have it installed on my personal gun and it works flawlessly. However, results may vary and might need modification to work in semi auto mode. This gun is similar to the Bullmaster and others have been able to fix the issue by replacing the spring. Go to your hardware store and look for a lighter spring. I got mine from Ace hardware and it fixed the magazine indexing issue. Features: Compatible up to .30 caliber Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

Sold out

Hatsan Blitz M18X1 Adapter ... $40.00

This adapter allows you to screw on an airgun suppressor with M18x1 threads. ***New Improved For More Air Flow.*** I recommend going with the Ronin with this gun. I have it installed on my personal gun and it works flawlessly. However, results may vary and might need modification to work in semi auto mode. This gun is similar to the Bullmaster and others have been able to fix the issue by replacing the spring. Go to your hardware store and look for a lighter spring. I got mine from Ace hardware and it fixed the magazine indexing issue. Features: Compatible up to .30 caliber Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip Important information: The only Moderator that is recommended with the Blitz is the RONIN .25/.30 M18, #S20A CLICK HERE

Hatsan Bullmaster/Galatian 1/2 x 20 Adapter A35

Hatsan Bullmaster/Galatian ... $40.00

1/2 x 20 UNF adapter for those rapid firing Bullmaster. New and improve design to allow more air flow. Please note that when you add a suppressor to this gun, it does not properly index the magazine. It uses blowback air to advance the magazine however with a suppressor on, it over rotates and causes it to not properly index. If you plan to single load it'll work fine. Some customers have been able to get the gun to work properly by swapping out the spring inside the shroud with a different strength one. Will take trial an error. Similar to the Blitz, this guy may need a lighter spring to work with a suppressor. I got mine from Ace hardware. See picture Features: Compatible up to .30 caliber Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

Hatsan Pile Driver Adapter $45.00

Features: Compatible with .45 and .50 caliber Made of steel M18x1 threads compatible with Emperor with M18x1 endcap Comes with black anodized Aluminum thread protector Adapters are tight fit and has four set screws (M4) to help secure it onto the barrel Uses 2mm hex keys for set screws

Hatsan QE 1/2 x 20 Adapter A24 $45.00

If you have a Hatsan Bully .25/.30- based on customer's feedback, I would go with the Emperor. *We have not had any success with customers using a suppressor on Hatsan's line up of semi auto guns. It causes the gun to not index properly. Features: Matte black Anodized CNC Includes knurled thread protector Compatible up to .30 Compatible with the following guns: Hatsan GladiusHatsan Flash Wood QEHatsan AirMaxHatsan Bullboss QEHatsan BT65 QEHatsan Nova QEHatsan AT44-10 QEHatsan Hercules QEHatsan Flashpup QEHatsan AT P1Hatsan Flash QE

Hatsan QE Big Bore .357/.457 M18x1 Adapter A54

Hatsan QE Big Bore .357/.45... $45.00

Features: Matte black Anodized CNC Includes knurled thread protector Compatible for the .357 and .457 model

Hatsan Riptor 1/2 x 20 Adap... $40.00

Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Grey anodize Diamond pattern knurling for easy grip Compatible with .22 and .25 calibers

Hatsan Sortie 1/2 x 20 Adap... $40.00

Features: *Warning, suppressors do not work well on Hatsan's line up of semi-auto guns. It will disrupt the magazine index and will not index properly. Use this adapter only if you plan to single load. Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

Sold out

Huben GK1 Pistol - A116 $35.00

This adapter allows you to add a 1/2 x 20 moderator or muzzle brake to your fun little pistol. Features: 6061 T6 Aluminum Black Anodize Knurled thread protector

Huben K1 1/2 x 20 Adapter A9 $40.00

Does not work on first gen Hubens Features Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

JKHan Noblesse .357 M18x1 A... $45.00

Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .357 Ronin and .357 Emperor

Sold out

JTS Aircuda / JTS Aircuda MAX Adapter .22, .25, .30 A115

JTS Aircuda / JTS Aircuda M... $50.00

Elevate your shooting experience with the DonnyFL JTS Aircuda and Aircuda MAX Adapter. Expertly crafted to let you seamlessly attach a DonnyFL Moderator to your rifle, this adapter ensures you can shoot with enhanced precision and reduced noise. Key Features: Compatibility: Perfect fit for JTS Aircuda and Aircuda MAX rifles. Suitable for .22, .25, .30 caliber variants. Premium Material: Made with high-grade 6061 aluminum, ensuring durability and a lightweight feel. Because this adapter was made to fit both the Standard and Max versions of the AirCuda, and because of the variations between individual rifles, you may find that one or two threads remain exposed when you snug the adapter in place. This is normal, and will not effect the performance of the rifle. In fact, our testing has revealed that a longer or heavier moderator can be used with less risk of clipping as compared to the endcap-only style adapter. It was necessary to design in this flexibility to overcome the challenges of this airgun's shroud design so that moderators can be used.

Find anything you need