Products

This beautiful pistol has a little bark to it. Add this adapter to it and your favorite suppressor to make it more enjoyable . Features: through hole in 1/2 x 20 threads for easy tightening or removal hole on side of adapter in case adapter is stuck in suppressor knurled cap CNC Matte black anodize

There are two options for the BP17 Option 1: If you would like to keep the factory shroud and add a suppressor to the end of it get #A49 Option 2: If you would like to remove the factory shroud and keep the gun as short as possible with a suppressor, select #A74. This is the version Ted did a review on.

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .357 model

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .22 and .25 calibers

This adapter replaces the factory baffle allowing you to screw on a 1/2 x 20 airgun suppressor. You will need to remove the factory o'ring and put it on the new adapter. Features: 6061 aluminum T6 Black anodized Knurled thread protector

This design goes back to the barrel and slides over the barrel bushing. This will keep the barrel aligned with the adapter's exit hole. Please note that the barrel bushing is not included. Factory gun already includes the bushing. The .357 Benjamin Bulldog is becoming popular for big game hunting. Add this adapter and pair it up with a .357 Ronin or .357 Emperor to make it the ultimate hunting airgun. I would recommend going with minimum the .357 Ronin for this gun. The .357 FX suppressor is not enough to quiet this gun down. IF you use an Emperor with this gun, do not add the extender. Too much weight added applied to the adapter and may cause inaccuracies.  Made by CNC for accuracy Very easy to install. Remove the top and bottom screw securing the front cap and swap it out for this adapter. Screw the two screws back in and you're done. No need to remove the shroud. Matte Black anodize Knurled thread protector When putting this on, press the adapter into the shroud as you tighten the two screws. This will ensure the adapter is flush with the shroud.

*Note: For the Akela, remove one of the factory baffles in order for the adapter to fit flush. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .177, .22 and .25 calibers

Features: This adapter has a 1/2 x 20 adapter at the end Has two holes on top like OEM so you can use original screws and front site. Overall length from one end to the other is 3.12 inches has groove underneath just like OEM for ease of removing fill cap CNC Matte Black Anodize Match this up with a .22 Tatsu and you have a nice quiet gun.

Want to make your Prod quieter? You'll need this 1/2 x 20 adapter, it will screw into the OEM shroud. The threads that screws into the shroud is 11/16 - 24.  The Sumo 1/2 x 20 is my favorite suppressor for this gun. However, in order to fill this gun with the Sumo, you'll have to remove the suppressor. An alternative is to go with either the Tanto or KOI with cone rear cap. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

This adapter extends the shroud 1.5 inches or about 38.1mm. Pair it up with a .22-25 Tanto 1/2 x 20 Bolt #S69 and this pistol will be very quiet. No need to remove the suppressor to fill the gun. Features: 6061 Aluminum Black anodized Comes with knurled thread protector  

Marauders are great entry level PCP guns. There are lots of mods you can do to make them more powerful. More power means a louder gun. To make it backyard friendly, make sure to grab this adapter to allow you to screw on an aftermarket LDC. Threaded end that goes into the OEM shroud is 13/16 - 28. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

Are you tired of going to the dive shop to fill your scuba tanks? Big Foot will solve that problem for you without spending over $2,000! It's portable, has an auto condensation drain and easy to haul anywhere. If you need to take it on a trip, as long as there's a 110v outlet around, you and your group are set! Big Foot does it for you! Note*Discounts do not apply Features: Max fill pressure 4500 psi Adjustable pressure setting Built-in double filter Compatible with 110v wall outlet Digital Display to show machine temperature Auto shutoff Auto condensation drain Water / Fan cooling 97 lbs 22.83"L x 20.47"H x 18.90"W 1 year limited warranty Recommendations: Use Distilled water For coolant use Royal Purple Purple Ice Cooling system optimizer  For oil, Royal Purple SYNFILM RECIP 100   SETUP GUIDE:  

Want to make your Compatto quieter? You'll need this 1/2 x 20 adapter that will screw into the OEM shroud. The threads that screws into the shroud is 11/16 - 24.  Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

This slide on adapter will fit the Bushbuck up to .45 cal. I would recommend the .45/50 Emperor v3 along with the 6.5 inch extender to tame this beast!

This is a slide on adapter for the Crosman 2240, ID measures 7/16.

This adapter converts the factory shroud threads from M20x1 to 1/2 x 20. Features: Aluminum 6061 T6 Black anodize Comes with knurled thread protector

You'll need this 1/2 x 20 adapter if you can't get the OEM adapter off the airstream that came with the gun.   Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .177, .22 and .25 calibers Remove factory suppressor and screw this into the shroud directly onto the barrel.

A perfect collector's item or gift.  Roughly the size of a quarter, 1 inch diameter weighing in at 0.4 oz.